[Size] ・Body: W36 x H70 x D19mm ・Sirens: W39.5 x H48 x D23.5mm
[Specification] <> ・Rated voltage: DC12V ・Operating voltage range: DC7V-17V ・Current consumption: 0.9mA or less (in standby mode) <> ・Model: Piezoelectric type ・Output sound pressure level: 122±5dB / 12V / 10cm ・Frequency: 2-4KHz <> ・Model: LED (Light Emitting Diode) ・Emission color: red
[Set components] ・Main Unit x 1 ・Siren x 1 ・LED Indicator Lamp x 1 ・Electro Tap x 2 ・Instruction Manual
*Please be sure to read the instruction manual before installation. *Professional knowledge and experience are required to install this product.If you are not confident about the installation and wiring, it is recommended to rely on the experts for your safety. *This product is for 12V motorcycles.This product cannot be installed on battery-less vehicles. *It may not be able to be installed on some vehicles. *This product does not completely prevent theft, but is an auxiliary device to prevent theft.No warranty is provided in the event of theft or misuse. *This product is not waterproof.Install the unit in a location where it will not be exposed to water. *Install the main unit, siren and wiring in a place where they cannot be seen from the outside. *This product cannot be installed on vehicles equipped with keyless entry. *After installing this product, periodically inspect it to see if any parts have fallen off. *PROTEC is not responsible for any damage or accident caused by the use of this product. *Please note that Protec cannot be held responsible for any accidents or injuries that may occur if this product is modified. *Protec is not responsible for any labor charges for removal or other expenses incurred during repair.
■High performance digital 3G sensor! ・This is a special kit for a long-selling burglar alarm that is easy to use even for beginners. ・No remote control required.The setting can be easily canceled only by operating the ignition key ON / OFF! ・The digital 3G sensor sounds a 122dB alarm when the vehicle's attitude changes by more than 5 degrees. ・The feature of the kit is that it comes with instructions on where to install the sensor, siren, and indicator LED, as well as instructions on how to connect the wires, so you can easily install it without worrying about the placement of each part, unlike universal kits. ・The wiring of the sensor itself has been adjusted to the appropriate length for the model of vehicle, so it can be installed neatly without unnecessary long wiring getting in the way. ・The alarm can be easily set on either the side stand or center stand.
[installation instructions] ・Remove the seat and the left side cover. ・Attach CS-550M sensor unit on the bracket holding the battery, and connect the red cord of the sensor unit to the positive side of the battery and the black cord to the negative side.The sensor body is attached with double-sided tape, but it is recommended to fix it with a bundle band to prevent malfunction. ・There is a red rubber cover on the plus side, so if you put the red cord through as shown in the image, you can cover the rubber cover nicely. ・The speaker is attached to the outer side of the battery case in the left side cover and connected to the sensor itself. ・Remove the cover from behind the rear fender.The yellow circles have two screw locations, and the red circles have two push rivets.Remove them all and the cover will come off. ・The waterproof 3P coupler of the taillight is located in the translucent rubber cover circled in red in the image.The wiring is a waterproof coupler with three wires (black, green, and green / yellow), so it should be easy to find. ・Connect the orange cord of the sensor to the black cord of the taillight with an electro tap. ・Attach the indicator light to the frame between the tank and the top bridge.Connect the cord of the sensor body, and put the seat and the left side cover back together to complete the work. ・It takes about 30-40 minutes to get here.The installation position of the sensor and siren is shown in the instruction manual, so it is very easy.
[operating instructions] 1) Stop the engine with the key OFF. 2) Turn the key ON and immediately turn it OFF. 3) A short beeping sound is heard, and the red indicator light shines for 0.5 seconds, then goes out for 2 seconds, and the operation is repeated. 4) The alarm is set.
The siren will not sound for about one minute after the alarm is set, even if it detects an abnormality, but the indicator lamp will flash at high speed. When an abnormality is detected after one minute, the indicator lamp flashes rapidly and the siren emits a loud alarm sound of 122db.
* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
Get on your grid by register your motorcycle! About our "Mybike" service
"Easier to Search Items" It helps you to search items to fit for your motorcycle!
"Get Much Valuable Information" It helps you to get special deals, newly listed items and closeouts about your motorcycle!
"Easy to Register" It requires only your motorcycle manufacturer, model name and model year!