awesome handlebar, comfort in riding. gives you a good posture when riding long distant. great item.fitted nicely for the bike.
Fits: HONDA FTR223 (without side numbers) * Requires modification of the clutch cable and choke cable., HONDA CB750 04- RC42 *Processing of switch hole required|* Required side cap (for 18mm ID), HONDA CB400SF 99-07 NC39 VTEC *Processing of the switch hole is required|* Required side cap (for 18mm ID), HONDA CB400SUPER BOLDOR 05-07 NC39 *Processing of switch hole required|* Required side cap (for 18mm diameter), HONDA CB400SF 99-07 NC39 VTEC III* requires drilling of switch hole|* requires side cap (for 18mm ID)
Reasonably priced item. Seems a fraction bigger than the stock parts. As a result the switch housings and riser clamps appear to have more of a gap between them after installing this bar. The paint also seems very susceptible to scratches. The part that attached to the risers are smooth, not knurled so there is a greater tendency for them to rotate unintentionally. Came packaged in corrugated paper (see attached image). On the w800 these bars give a narrower but more upright feel. if you are using bar end mirrors, take note that the increased swept back angle means that your rear view might not be wide enough.View Detail
Fits: HONDA FTR223 (without side numbers) * Requires modification of the clutch cable and choke cable., HONDA CB750 04- RC42 *Processing of switch hole required|* Required side cap (for 18mm ID), HONDA CB400SF 99-07 NC39 VTEC *Processing of the switch hole is required|* Required side cap (for 18mm ID), HONDA CB400SUPER BOLDOR 05-07 NC39 *Processing of switch hole required|* Required side cap (for 18mm diameter), HONDA CB400SF 99-07 NC39 VTEC III* requires drilling of switch hole|* requires side cap (for 18mm ID)
Prefect lowered handle bar and the colour are nice finishing. Needed risers as too low and the switches hits the sides fairings n tank. Switches needed to drill as it do not comes together with holesView Detail
Fits: HONDA FTR223 (without side numbers) * Requires modification of the clutch cable and choke cable., HONDA CB750 04- RC42 *Processing of switch hole required|* Required side cap (for 18mm ID), HONDA CB400SF 99-07 NC39 VTEC *Processing of the switch hole is required|* Required side cap (for 18mm ID), HONDA CB400SUPER BOLDOR 05-07 NC39 *Processing of switch hole required|* Required side cap (for 18mm diameter), HONDA CB400SF 99-07 NC39 VTEC III* requires drilling of switch hole|* requires side cap (for 18mm ID)
This is a change from Plating of the same type.
On the LeftGrip side, there is a paper seal with the product number, ManufacturerMain and product name, which is still difficult to remove.
If you could make it easier to peel off, I'd appreciate it.
Also, when I peeled off the seal, I found a hole in it. I don't understand why there is a hole in it.
Also, I'd appreciate it if HURRICANE would do an OrderHandlebar or something!View Detail
Fits: HONDA FTR223 (without side numbers) * Requires modification of the clutch cable and choke cable., HONDA CB750 04- RC42 *Processing of switch hole required|* Required side cap (for 18mm ID), HONDA CB400SF 99-07 NC39 VTEC *Processing of the switch hole is required|* Required side cap (for 18mm ID), HONDA CB400SUPER BOLDOR 05-07 NC39 *Processing of switch hole required|* Required side cap (for 18mm diameter), HONDA CB400SF 99-07 NC39 VTEC III* requires drilling of switch hole|* requires side cap (for 18mm ID)
I got a raggedy VCR and the Handlebar that came with it was so lame So
I couldn't help but buy it
And the texture is good and works fine
It's nice to have a low price and easy to buy
View Detail
Fits: HONDA FTR223 (without side numbers) * Requires modification of the clutch cable and choke cable., HONDA CB750 04- RC42 *Processing of switch hole required|* Required side cap (for 18mm ID), HONDA CB400SF 99-07 NC39 VTEC *Processing of the switch hole is required|* Required side cap (for 18mm ID), HONDA CB400SUPER BOLDOR 05-07 NC39 *Processing of switch hole required|* Required side cap (for 18mm diameter), HONDA CB400SF 99-07 NC39 VTEC III* requires drilling of switch hole|* requires side cap (for 18mm ID)
A little less than the bar I've had so far Spec. I want to change and purchase
Since COSPA is excellent, I will try to purchase as much as I try
What is disappointing is the shape Quantity : Pair (for Left and Right) There is a little deviationView Detail
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING