Touring Carrier Off-Road Line

Fits:HONDA XR400 Other information]T-2, HONDA XR250 95 -, HONDA XR250 BAJA 95-

Japanese Webike user

Very Good

Apr 10, 2022

Heavy but looks sturdy

We chose this one because we wanted to increase Frame rigidity by integrating it with the Sub-frame, even if it increased in weight.
The installation of the Seat was done by inserting a washer in a hurry because the collar was not thick enough to hold the Seat together and the installation part started to bend during temporary tightening.
The hole positions are perfect, and it would be perfect if there were additional thicker colors in the Included Parts:section.

Helpful?

Fits:HONDA XR400 Other information]T-2, HONDA XR250 95 -, HONDA XR250 BAJA 95-

Japan User(translated)

Average

Jul 26, 2010

Storage of a motorcycle is under a carport.
Coating of the end of a square pipe will begin to break after use in about four years. A part of coating will separate in five years, and it is rust generating.
Comparatively [ back long ], a carrier has not carried what has rigidity it is low and right [ that ] and not much heavy.
Possibly the short type was better.
(It exchanged for the somewhat small carrier made from the aluminum of the other company later.) The weight of a carrier is about 1.5 kg.
(The carrier made from aluminum is about 0.8 kg.)

Helpful?

Fits:HONDA XR400 Other information]T-2, HONDA XR250 95 -, HONDA XR250 BAJA 95-

Japan User(translated)

Very Good

Aug 10, 2009

Since the iron square pipe is used, the rigidity of appearance is reliable.
According to the nickel plating color, the black bolt of the bolt was more desirable.
Serviceability fell.
A battery and the work which removes a sheet became troublesome.
A hole site is coarse and SHINO is required for it.
Although until does not say, it has required power with a frame or the carrier impossible for itself.
A frame may distort or go out owing to a carrier.

Helpful?

Unbrowned loads are unsettling.

Fits:KAWASAKI KLX250 , KAWASAKI D-TRACKER -07

Japanese Webike user

Average

Sep 1, 2021

I installed this on my 2001 dTRACKER.
Bolt at the attachment point to the vehicle body is M6 and Quantity:2pc and M8Quantity:2pc only.
The carrier itself looks sturdy, but I'm not sure I'd be able to carry a full set of camping gear in a box like this.
I think it is better not to load the cargo without Brown too much.

Helpful?

Installation is odd but very easy to use

Fits:SUZUKI RMX250S 96-

Japan User(translated)

Very Good

May 4, 2020

I wanted to add the GIVI MonokeyPannier that I'm using on my ZX11 I bought it as a base The installation is two Bolts for the installation of Small Bag and Seat & Side cowl installation BoltQuantity:Pair (for Left and Right) (For Bolt length change, it comes with the product), but you can use the Accessory Case side When you install from Bolt, the position to put the Bolt of Seat and co-tightening is about 3cm above Gap The order is to put in the Seat and the Bolt side of the co-tightening, then the Accessory Case side As an order, put in the Bolt side of the Seat and co-tightening first, then the Accessory Case side Put the bolt of the Seat side If you don't do the same order of tightening, the bolt of Seat side will be broken It may be a bit dull, but the bolt of Seat side is the standard, and the bolt of the Accessory Case side is more than appearance Secure it at an angle that rises to
I'm using this with a Mount base for Monokey in my Pannier It is very rigid and of good quality and does not wobble at all There are also enough of them for Carrier to get full marks